Kabler og adaptree/Energi/Støpsel

SmartLife Smart Plug

Wi-Fi | Efektmåler | 2500 W | Jordet kontakt / Type F (CEE 7/7) | -10 - 40 °C | Android™ / IOS | Hvit | 1 stk.

Egenskaper

Leverandør Delenummer: WIFIP110FWT
Strek nummer: 5412810269945
• kan brukes som et frittstående produkt eller enkelt kobles til andre Nedis® SmartLife-produkter
• gir automatisk fjernstyring - for å sette opp tidsplaner og koble sammen apparater
• støtter talestyring - i kombinasjon med Amazon Alexa eller Google Home
• slank utforming - for å sikre at tilstøtende stikkontakter ikke blokkeres
Fjernstyr en rekke elektriske apparater ved å plugge dem inn i denne trådløse smartpluggen og koble dem til en smarttelefon eller et nettbrett via Wi-Fi-ruteren din. Med den praktiske strømmåleren kan du umiddelbart se hvor mye strøm apparatet bruker i dette øyeblikket, eller hvor mye strøm den har brukt over tid.

Enkelt å sette opp
Du trenger ikke å være et teknisk geni eller elektriker for å kontrollere og automatisere de innkoblede apparatene og enhetene dine. Alt du trenger, er en smartplugg og Wi-Fi-ruteren din. Den intuitive appen vår gir deg mulighet til å slå apparater av og på eksternt og automatisk. Den kan til og med fungere sammen med talestyringssystemer som Amazon Alexa eller Google Home.

Superslank - aldri mer blokkerte stikkontakter
Disse superslanke apparatene er utformet for å unngå det vanlige problemet der smartplugger blokker tilstøtende stikkontakter - pluggene våre er både smarte og slanke med tanke på praktiske utfordringer.

Sett opp tidsplaner og koble sammen
Sett opp tidsplaner for når pluggen skal slå på apparater eller koble dem til andre, for å skape stemningsfulle scener som kan aktiveres med en enkelt kommando eller trykk på en knapp.

Overvåk strømbruk
Oppdag umiddelbart om apparater bruker for mye strøm, for å sikre at du bor i et smart og energieffektivt hjem.

Om Nedis SmartLife
Oppdag et bredt og stadig større utvalg av produkter - som pærer, brytere, kontakter, sensorer og kameraer - som kan styres gjennom en brukervennlig og intuitiv app. Talestyringsfunksjoner er støttet av Amazon Alexa og Google Home, og du trenger ikke noe annet enn et eksisterende Wi-Fi-nettverk. Dette er det sammenkoblede, smarthjemmet gjort på den enkle måten.
Enten du ser etter en enkel smart pære eller kontakt eller ønsker å automatisere hele huset, vil disse løsningene vise deg hvor tilgjengelig smartteknologi er i dag.

Emballasje

Innholdet i pakken

Smartplugg
Hurtigveiledning

Forpaknings størrelse Gaveeske med eurolock

Bredde Høyde Lengde
105 mm 125 mm 63 mm

Logistikk størrelse

Antall/kartong Bredde Høyde Lengde Vekt
1 65 mm 150 mm 110 mm 107 g
50 345 mm 285 mm 560 mm 6000 g

Produktspesifikasjoner

Bredde 45 mm
Høyde 70 mm
Dybde 45 mm
Vekt 57 g
Farge Hvit
Materiale Plast
Kompatibel med Nedis® SmartLife
Maksimal antenneforsterkning for overføring 1.5 dBi
Maksimal overføringseffekt 14 dBm
Efektmåler Ja
Enhetens inngangsforbindelse ® Hybrid (CEE 7/7)
Utgangseffekt 2500 W
Input Current 10 A
App tilgjengelig for Android™
IOS
Send frekvensområdet 2412 - 2472 MHz
Nettplugg Type F (CEE 7/7)
Emballasjetype Gift Box with Euro Lock
Støttet trådløs teknologi Wi-Fi
Utgangsstrøm 10 A
Antall produkter i pakken 1 stk.
Driftstemperaturområde -10 - 40 °C
Enhetens strømuttak Jordet kontakt / Type F (CEE 7/7)
Type av jording Jordet kontakt
Inngangsspenning 230 V AC

Støtte

Vanlige spørsmål

Vi har funnet følgende spørsmål til deg på engelsk

Go to the settings menu of the plug > remove device and data
Then go to Profile > settings > clear cache
Now reset the plug and add it back to the app

Please try the AP mode.

Make sure that you use a 2.4Ghz wifi network.

Reset the plug so it blinks slow.

If it blinks fast, reset it again and it will blink slowly



In the app:

+ > [your device] > tap on EZ mode and select AP mode > confirm it was reset > fill in the info of your wifi network > follow the steps in the app.



Hold your phone very close to the plug during the installation

This method uses a direct connection to the device to send the info of your wifi to it.

Holding it close optimises this connection

Nedis Smart plugs are designed and tested to be used as power supply for consumer products. Since there are no applicable standards developed yet Nedis Smart plugs are not designed and not tested to be used as a feed-in component into a power grid and/or to be used in combination with solar (balcony) panels.

Nedis Smart plugs are designed and tested to be used as power supply for consumer products. Since there are no applicable standards developed yet Nedis Smart plugs are not designed and not tested to be used as a feed-in component into a power grid and/or to be used in combination with solar (balcony) panels.

To control your Nedis SmartLife products with Google Assistant, you need to assign your Smart Life products in a room also in Google home.

1. Start the Google home app.
2. choose Settings
3. choose More Settings
4. Go to the tab off your home.
5. If a device is not assigned to room, tab on the device name and assign it to a room.

Now, you can control your devices by Google home products.


Add the "Smart Life" service to Google Home (no Nedis in the name).

Go in Google Home to Assistent -> Home Control and choose here "Smart Life" as service.

Use the Login details of the "Nedis Smartlife" app.
Compatible Nedis SmartLife products will then be added to Google Home.

An automation can be used to make a certain "event"(condition), trigger another action (Task)
A condition can be anything from motion detection, to a certain time, a certain temperature, sunrise.
Then you can make this condition turn on lights, turn on smart plugs, make a siren sound or a combination of multiple tasks.

You can add maximum 20 members.

Yes you can.
Each person needs a unique account on their mobile device.
To add them as "family members" follow these steps:
In the main screen of the app tap on the name of your home (top left)
Tap on Home management
Tap on the name of your home again.
Tap on "add family members" and fill in the account details of the person you want to add.
It will give them access to all the devices in your home as a normal member or admin (you can select this)

If you only want to share a single device in a home, go to the settings menu of the device and select "share device" -> add member.

This is probably a Wifi problem, this can be for various reasons.
1.) Wifi signal is unstable.
2.) Wifi signal is too weak.
3.) Using an access point with the same SSID and password that do not support the IEEE 802.11R standards.

Problem 1 can often be solved by restarting the router.
Problem 2 can be checked with an app Wifi analyzer with this the signal can be viewed and corrected to a better position.
Problem 3 can be checked as the access points are turned off, the Wifi signal is still good and the connection remains if the access points are a problem, a Mesh solution can then be used.
Please make sure that they support IEEE 802.11R standard.